Hyd-mech s-20 parts manual

Table of Contents. Previous Page. Next Page. MECH band saw. Put Safety First Mandatory Information — This Safety Section contains important information to help you work safely with your machine and describes the dangers inherent in our machines.

Some of these dangers are obvious, while others are less evident. Name Date Signature Page 8: Basic Rules Manual. Hyd-Mech Group cannot accept any liability for personal injury or property damage due to operator errors or non-compliance with the Safety and Operating Instructions contained in this Manual. Page 9: Responsibilities Of The Owner Responsibilities of the owner Organization of work This Operation and Maintenance Manual must always be kept near the machine so that it is accessible to all concerned.

The general, statutory and other legal regulations on accident prevention and environmental protection must also be observed, in addition to the Manual material. Page Responsibilities Of The Operator And Maintenance Personnel Responsibilities of the operator and maintenance personnel Safety equipment All machines are delivered with safety equipment that must not be removed or bypassed during operation. The correct functioning of safety equipment on the machine must be checked: at the start of every shift.

Page 11 Gloves Experience has shown that careless use of gloves around machinery is a major factor in serious hand injuries. Gloves should not be worn when operating or adjusting the machine, except: Wear protective gloves when handling bandsaw blades at blade changes.

Gloves may be worn when handling work pieces, only if the machine is in Manual Mode and the bandsaw blade is not running. Page 12 On Hyd-Mech machines the Master Disconnect Switch will be of one of three types: Rotary switch mounted in electrical control cabinet door and inter-locked with door It is essential that operators be alerted to the safe opera- tion of this saw, and the practices to avoid that could lead to injury.

The following safety rules are at the minimum neces- sary for the safe installation, operation, and maintenance of the saw. Substitutes must be of the same vis- cosity in order for the system to work properly. The supply voltage of the machine displayed on the Serial Plate and the voltage label. A suitable strain relief should be used. All of the electrical functions and the Feed Rate setting are operated from the control panel. Adjustment should be made only when the blade is running.

Blade Start 5PB — A green push button. It took brains, dedication, a great deal of hard work. She was still talking about the flying. Then, realising how that might have sounded, he very nearly blushed himself.

More action and two Mets crossed the plate. When Ed Charles made the third out the score was tied, and as the commercial started she pushed the button, looked at me, and said, "Call Wolfe and tell him I want to see him. The idler side guide arm is adjustable for proper spacing and movement supported by a linear bearing. Powered Blade Brush Driven off the blade drive wheel the blade brush keeps the blade gullets clean, helping to maximize blade performance and life.

Blade Tensioning Mechanical tensioning assembly allows for quick and simple blade changing. A LED display provides readout for proper tension setting. Machine will not operate unless proper band tension is applied.

Coolant System A centrifugal pump delivers ample coolant on the cutting area. The coolant flows through both drive and idler guide blocks with flow valves for quantity adjustment. Quick Links. Our goal is to change. Please use this manual to familiarize yourself and your employees on the proper operation and.

We appreciate the confidence you have shown in our product and wish you every success in its use. Previous Page. Next Page. Troubleshooting Maintenance and troubleshooting 17 Troubleshooting Guide Our goal is to change stock cutoff from a "necessary evil" to a money making and time saving part of your operation.

Page 4: Safety Precautions TION Upon delivery of your new S Series II saw, it is imperative that a thorough inspection be undertaken to check for any damage that could have been sustained during shipping. Special attention should be paid to the electrical and hydraulic systems to check for damaged cords, hoses and fluid leaks. When lifting the pallet with a forklift truck make sure that the load is firmly balanced.

The following photo shows a lift truck lifting the saw and pallet from the correct side. The supply voltage of the machine is displayed on the Serial Plate and the Voltage Label. Substitutes should be an "EDM" fluid code which is equal in viscosity to a 5 hydraulic oil.

The cylinder contains oil in a reservoir that should be topped up to the level of the filler plug. Add oil to the cylinder only with the Head in the Head Down position. Page 10 Variable pitch see Pg 2. The Head swing of the S Series II is easily changed to set a different cutting angle by first releasing the Angle Brake lever, and then manually moving the Head to the cutting angle desired.